socalf32ax.blogspot.com
John's F32ax: Where to Build?
http://socalf32ax.blogspot.com/2008/01/where-to-build.html
A construction diary of a home-built Ian Farrier F-32ax. Wednesday, January 30, 2008. Due to the space requirements of the F-32, the only place possible to do this project is my backyard. I really like Jay's ( http:/ seattle-f22.blogspot.com/. Approach so I decided to do the same. The boat will be built in the tent and I will vacuum bag and fabricate parts in the garage. Here are some pics of my backyard boathouse:. Sorry honey, that tree's gotta go! Subscribe to: Post Comments (Atom).
davesf-32.blogspot.com
Dave's F-32AX Trimaran: May 2015
http://davesf-32.blogspot.com/2015_05_01_archive.html
Building a f-32 trimaran. Wednesday, May 13, 2015. The start of the 2015 boating season May 10 2015. Subscribe to: Posts (Atom). View my complete profile. RW's Farrier F82R - "Chillax". Tom and Cora's F-32. The start of the 2015 boating season May 10 2015 . Watermark template. Powered by Blogger.
lydiusmarius.blogspot.com
Lydius-F82R: January 2009
http://lydiusmarius.blogspot.com/2009_01_01_archive.html
The building of the Ian Farrier designed F82R trimaran. Sunday, January 25, 2009. Lower port hull planked and HD inserts. The planking of the lower hull is now ready to fit HD inserts , short for high density ( hard foam 200 kg/m3). These pieces are used everywhere compression will occur, like fitting locations, but also along keel for trailering loads. First I had to fit another batten on top to hold the extra foam, needed for vacuumtape. Test fitting the HD strip. Links to this post. As Jess is moving ...
lydiusmarius.blogspot.com
Lydius-F82R: Summer update
http://lydiusmarius.blogspot.com/2011/08/summer-update.html
The building of the Ian Farrier designed F82R trimaran. Wednesday, August 17, 2011. Interior is ready to get boat out of the mold. Lots of firewood for the winter. Filling holes and seams to infuse the bottom. Deck infused, I choose to do it in two tempies, since working with the boat on the side makes it quite high. Cockpit floor reinforced with layers of unicarbon both sides. An other layer of glass will be added once the stern is ready. Subscribe to: Post Comments (Atom). What is a F82? I use the Aust...
lydiusmarius.blogspot.com
Lydius-F82R: June 2012
http://lydiusmarius.blogspot.com/2012_06_01_archive.html
The building of the Ian Farrier designed F82R trimaran. Friday, June 22, 2012. Rebuild of a F25 daggerboard. For my fellow trimaran owner/builder Per Folm Hansen I made an attempt to rebuild an older daggerboard to a High aspect shape that is Larry Wood that gave me the idea. Here I stripped the old glass from the foam/wood core after cutting to the new shape. I had to make a new carbonstringer that is build from normal and HD foam, then wrapped tight with two layer og 300 g/m 45/45 and infused with epoxy.
lydiusmarius.blogspot.com
Lydius-F82R: Taping ancher well floor and forward bulkhead
http://lydiusmarius.blogspot.com/2011/03/taping-ancher-well-floor-and-forward.html
The building of the Ian Farrier designed F82R trimaran. Monday, March 28, 2011. Taping ancher well floor and forward bulkhead. Hi there a note from the no-workspace-at-all department. I had to fit the bulkhead after this difficult task was accomplished, and tape the bottom part of the bulkhead using a mirror to see that I was doing OK. I was taping through a 15 cm hole for a inspectionhatch. Below a shot from inside the watertight compartment that show the tape is fitted well. March 30, 2011 at 4:09 AM.
lydiusmarius.blogspot.com
Lydius-F82R: February 2009
http://lydiusmarius.blogspot.com/2009_02_01_archive.html
The building of the Ian Farrier designed F82R trimaran. Wednesday, February 25, 2009. Fitting top to beams. Fitting top is strait forward. Masking tape is set on an angle on each bulkhead and web and a lot of bog filled into these triangels. Also edges got a nice big round of bog. I use glassbubbles for this bog. When top is fitted it is turned upside down so bog can form a triangel to top. Links to this post. Fitting strut bearing to beams. I bought a complete folding set from. A look inside beam. After...
lydiusmarius.blogspot.com
Lydius-F82R: Rebuild of a F25 daggerboard
http://lydiusmarius.blogspot.com/2012/06/rebuild-of-f25-daggerboard.html
The building of the Ian Farrier designed F82R trimaran. Friday, June 22, 2012. Rebuild of a F25 daggerboard. For my fellow trimaran owner/builder Per Folm Hansen I made an attempt to rebuild an older daggerboard to a High aspect shape that is Larry Wood that gave me the idea. Here I stripped the old glass from the foam/wood core after cutting to the new shape. I had to make a new carbonstringer that is build from normal and HD foam, then wrapped tight with two layer og 300 g/m 45/45 and infused with epoxy.
lydiusmarius.blogspot.com
Lydius-F82R: March 2009
http://lydiusmarius.blogspot.com/2009_03_01_archive.html
The building of the Ian Farrier designed F82R trimaran. Monday, March 9, 2009. A virtual trip down under. Links to this post. My own 18 foot skiff BODOTEX. Links to this post. Subscribe to: Posts (Atom). What is a F82? A fast cruising/racer trimaran 8.2 m long. The boat can fold to go on a trailer. As seen here you can go anywhere with this boat. The former model F25C. A virtual trip down und. My own 18 foot skiff BODOTEX. Boatbuilder of the old school, but building this very modern boat for myself.
SOCIAL ENGAGEMENT