ottawarobotics.org
Line Following – Ottawa Robotics Enthusiasts
http://www.ottawarobotics.org/line-following
Hobby roboticists in Canada's national capital region. Build an autonomous robot that can follow a black line on a light coloured, flat surface. There are two levels of competition: beginner and advanced. These designations are based on the level of difficulty of the line following maze. The course will be relatively simple (no right-angles) and short. The course will be relatively difficult (right-angles and tunnels) and long. Dimensions: Less than 30 cm wide, less than 30 cm long, no height limit.
ottawarobotics.org
Robomagellan – Ottawa Robotics Enthusiasts
http://www.ottawarobotics.org/robomagellan
Hobby roboticists in Canada's national capital region. Robots navigate a pre-defined course dealing with various obstacles along the way. Waypoints may be marked with objects that the robot must touch or come within a specified distance. The robots will be guided primarily by GPS and vision systems. Robots will be fully autonomous, but do not necessarily have to be self contained, i.e. it is ok to have a laptop with a wireless or even wired link to the robot. April 29, 2007. Running on netbook computers.
blog.ottawarobotics.org
Aaron Ramsey | Ottawa Robotic Enthusiasts Blog
http://blog.ottawarobotics.org/author/aaron
Ottawa Robotic Enthusiasts Blog. Hobby roboticists in Canada's national capital region. Author Archives: Aaron Ramsey. May 21, 2013. Just a quick video showing how I depanelize PCBs. I typically buy PCBs from SeeedStudio or iTeadStudio and it makes sense to use the 10cm by 10cm board size and jam more than one PCB into that area. Diptrace (my … Continue reading →. Lasering and 3D Printing. February 22, 2013. Printrbot Jr. saves the day. December 12, 2012. Printrbot Jr. Arrives…. mostly. October 12, 2012.
blog.ottawarobotics.org
Printrbot Jr. Arrives…. mostly | Ottawa Robotic Enthusiasts Blog
http://blog.ottawarobotics.org/2012/10/12/printrbot-jr-arrives-mostly
Ottawa Robotic Enthusiasts Blog. Hobby roboticists in Canada's national capital region. Holy Frikkin’ Laser! Printrbot Jr. saves the day →. Printrbot Jr. Arrives…. mostly. October 12, 2012. Its been a fun week… first the laser and now the Printrbot Jr. We weren’t going to build the printer until this weekend, but decided to take a look at all the pretty wood pieces. Printrbot has a nice diagram ( http:/ printrbot.com/wp-content/uploads/2012/10/Parts-Diagram-JRv18.pdf. We are missing part 326! I took the ...
blog.ottawarobotics.org
Lasering and 3D Printing | Ottawa Robotic Enthusiasts Blog
http://blog.ottawarobotics.org/2013/02/22/lasering-and-3d-printing
Ottawa Robotic Enthusiasts Blog. Hobby roboticists in Canada's national capital region. Printrbot Jr. saves the day. Depanelizing PCBs →. Lasering and 3D Printing. February 22, 2013. On a fixed base and got to business with lots of wood cutting. This week I finally had a chance to get back to figuring out the stencils. I ordered a roll of 3mil mylar from McMaster-Carr. I’ll be soldering with it tomorrow and will report back the results. Speaking of next weekend, there is a 3D Print-a-thon. Anyhow, the Pr...
ottawarobotics.org
Articles – Ottawa Robotics Enthusiasts
http://www.ottawarobotics.org/articles
Hobby roboticists in Canada's national capital region. The Sharp GP2D02 IR Distance Sensor. 8211; Interfacing and using the GP2D02, along with sweeping it back and forth so. That you don’t have to buy a bunch of the expensive little suckers. 8211; How to use a R/C hobby servo for robotics. RF Communications Primer for Robots. 8211; Several hints and code for using cheap RF transmitters/receivers for communication between robots. 169; 2012 Ottawa Robotics Enthusiasts. Suffusion theme by Sayontan Sinha.
ottawarobotics.org
Gallery – Ottawa Robotics Enthusiasts
http://www.ottawarobotics.org/gallery
Hobby roboticists in Canada's national capital region. More robots can be found on the following pages. Movie (avi, 3M). R2D2 movie (gp3 format, playable with VLC, GOM, RealPlayer). Created with the new Lego Mindstorms NTX. Close-up of the encoders. 8220;Taz”owner: Allen. 8220;Scrambler”owner: Steve. 8220; Sumo Bot. 8220;Model C-1″owner: Jin. A Roboflag entry from the Pathfinder team [info]. Pdf, 1.5M). Cover of “The Charlatan”. Owner: Jin hi-res pic. 2M – odd AVI format). 8221; (work in progress).
ottawarobotics.org
Control Boards – Ottawa Robotics Enthusiasts
http://www.ottawarobotics.org/control-boards
Hobby roboticists in Canada's national capital region. These are older designs from 2002 to 2008. You can find our modern designs on the wiki pages. On this page…. So, what is an IgORE? First, IgORE doesn’t actually stand for anything, other than the ORE part anyways. The board was designed to have the maximum amount of expandibility and use, based around a MicroChip PIC processor. It was originally meant to be for SUMO’s but could legitimately be the brains for any other ‘bot. 8211; (Dec 8th, 2002).
ottawarobotics.org
Mailing list – Ottawa Robotics Enthusiasts
http://www.ottawarobotics.org/list
Hobby roboticists in Canada's national capital region. ORE has a mailing list hosted through YahooGroups called ORE bits (Aren’t we the punsters, eh? The list is used to exchange information, hint and tips, as well as keep everyone informed of upcoming meetings and other functions in Ottawa that might be of interest to the group. The email list is the best way to keep on top of group going-ons. Join our mailing list. 169; 2012 Ottawa Robotics Enthusiasts. Suffusion theme by Sayontan Sinha.
